MPLAB X IDE

I am running MPLAB X IDE 5.20 after several years of absence. I'm trying to compile the code from AN1160 (BLDC code) for the Motor Control Starter Kit (Assy 02-02339-R2) using the dsP33FJ16MC1021ML. I am getting many errors such as: #include "periph.h" th..

Does anyone know what is causing this problem? Is there a fix for this?..

I have a project with a PIC32MZ and a bootloader. I am using a Pickit3 and MPLAB 3.35. My bootloader works as I want it for now. My app has some functionality I want to debug. I currently have the main project set to be the bootloader with the main-app se..

Hi guys, Am i missing some setting in MPLABX ?The data in the pointer is from a wrong address, it seems that only the lower Address byte is used in the watch windows of the debugger, in this case instead of showing contents at address x220 it shows conten..

Since i'm using version 5.25 of the MPLABX ide I do get an error >>Target Device ID (0x2000) is an Invalid Device ID. Please check your connections to the Target Device.<< when trying to program a device for the first time after having started the IDE.Aft..

Hi,i'm updating the toolchain on my macbook, but i keep getting network issues.It seems like the application is not allowed to use the internet? even though my internet connection obviously works, and the websites it tries to reach can be reached in a bro..

Greetings! I am making my first test with MPLab lib files. So I`ve made a lib project and compiled a .X.a file. So I`ve managed to add it to a new project and everything seems fine. I have a question. When I start the project with this precompiled lib and..

Test post. Unable to Post New Thread...

The comparator peripheral interrupt does not work?..

Hello, I created a project and when i tried to build it i couldnt because when i checked there wasnt any dist file to open. I dont know why it happened so i did the entire thing again creating a new project and setting the config bits again, and copied th..

Hi! I might sound stupid but please don't mind I am a fresher and just began to write drivers in samv71n19b. Previously I used atmel studio which is fine but someone suggested me to try MPLAB X. I have written a simple gpio driver to get familiar with thi..

This (Microchip) Eval board has its own built in PIC24-based debugger. I struggled to get the correct device drivers to install. Windows (7/64) was INSISTING it was a "USB Input Device" in Device Manager I fixed that by editing the .inf file ..

PIC24FJ32GA002 on MPLAB X 5.10 compiler XC16 rev 1.36 free licenseI am using a ICD3 I am having issues in that I cannot set the settings:

#pragma JTAGEN = OFF

#pragma IOL1WAY = OFF

When building I get:

../src/Hardware.c:9..

In MPLAB 8, once you had compiled your project you could get the Disassembly for the whole project. In MPLAB X, it seems that you can only get the disassembly if you're in Debug mode, and even then it only shows you the file that your program counter is c..

Hello,Is it possible to flash a hex file to the uC with a script? I did so with ARM microcontrollers, but didn't find any information for the PICs. I use ICD3 programmer. Thank you.Michael..

Hi, The behavior of the MCP2200 in that it chops up an incoming byte stream into chunks that are a maximum of 32 bytes of data in each packet means I will need to take on the task of creating my own USB to serial converter. I think the current productio..

Hi all,for the past 2 years one of the electrical engineers I work with has been designing control box around the ATMEGA2560. I cant really give away the full specification on here and hold on to my job but it does A LOT, loads of outputs, loads of inputs..

Hi,I'm moving from PIC18F47K40 to PIC18F47K42. The I2C module in the newer chip is trying to be smarter I think which means it is less than clear to me how it works and I think it has built in limitations that weren't there before...To start out I'm going..

Hello All, I am trying to use ceedling to automate tests for a PIC24FJ1024GB606. I currently have the same tests running on a PIC24FJ256GB106, but I want to simulate them on the correct chip. I am testing the ceedling settings by running sim30 test/simula..

Include paths for MPLAB X IDE 5.20 for legacy project (AN1160) (btremaine)

Could not acquire hardware tool communications resources: RealICEPlatformTool SN#xxxxxxxxx (jtorre)

Best way to "skip" bootloader while debugging? (NVergunst)

Why does MPLABX Vairables and Watch show pointers at a wrong address? (picmaster75)

Error during programming a device after start of IDE (pppGerm)

MPLABX 5.25 on OSX can't access the internet (so can't download plugins or packs) (JPortici)

MPLab precopiled library (stoyanoff)

Best way to "skip" bootloader while debugging? (NVergunst)

Test post. Unable to Post New Thread. (sebmadgwick)

dspic33ep256mc502 comparator peripheral (jimsullivan1)

Dist file gone !!! (aviator3679)

Steps are not sequential while Debugging (shabbir bohra)

MPLAB X 5.25 problem with PKOB for PIC32MZ board D320010 (boatbodger)

Problem with config: warning: ignoring #pragma JTAGEN (user2x)

Disassembly listing for whole project (Tumbler41)

Flashing uC with a script without MPLAB (nagogam)

Best advice for making a USB to serial converter (swmcl)

Moving from Arduino to PIC (bott)

New I2C module - more difficulty - PIC18F47K42 (swmcl)

SIM30 CORE-E0004 (SinCitiesSin)